High Quality Industrial Air Drying Regenerative Blower

 High quality Industrial Air Drying Regenerative Blower Our advantages : 

1. Adopt SKF & NSK bearing.
2. Use ADC12 aluminum alloy material.(same to BMW's wheel hubs)
3. Random installation( vertical or horizontal)
4. Insulation class: F, Protection class: IP54
5. 100% oil free air delivery ( Impeller connected to the motor directly, without any oil lubricating) 
6. No routine maintenance (whithout wheel gear and belt,don't need to do maintenance towards those parts)
7. Quiet operation, low noise(adopt low noise motor, meanwhile inlay muffler is available if lower noise required)
8.Variable output control(pressure or vacuum)
9.Pulsation-free compression(use quakeproof footstand)
10.Long term durability(24H running)
11.Strictly tested before leaving the factory


Applications : 

1. Aquaculture (fish and prawn pond aeration)
2. Waste water treatment, sewage treatment system.
3. Pneumatic conveying systems.
4. Lifting and holding of parts by vacuum.
5. Packing machines.
6. Filling of bags/bottles/hoppers.
7. Soil remediation
8. Food processing.
9. Laser printers
10. Dental suction equipment.
11. Paper processing.
12. Gas analysis.



Our service:
 Marketing Service
100% tested CE certified blowers.Special customized blowers(ATEX blower,belt-driven blower) for special industry.Like gas transportation,Medical industry...Professional advice for model selection and further market development.
After-sale Service
Experienced suggestion for blower installation and use.12 months warranty.Long-term technical support.





FAQs:
Q: Can water be pumped through my blower?
A: No, clean dry air only
Q: My blower is leaking around the cover is this normal?
A: Normal goorui blowers are not  leak-free designed,but if you care a lot about the leaking,then you can contact us for a leak proof  one(special customized).
Q: What kind of oil do I need for my blower?
A: All our goorui blowers are oil-free and maintenance-free designed.
Q: Can I pump combustible gas through my blower?
A: Normally,if you'd like to use blower for combustible gas conveying,we suggest to choose our explosion proof ATEX blower(special customized) .
Q: Are the foam pieces inside my blower for filtration?
A: No, they are not for filtration. They are designed for sound reduction, an inlet filter should be sourced separately.
Q: What will be the consequences if I don't use a relief valve on my blower?
A: The blower may get overheat, and may cause thermal expansion of internal parts, which will do harm to the impeller and Bearing.  High quality Industrial Air Drying Regenerative Blower Our advantages : 

1. Adopt SKF & NSK bearing.
2. Use ADC12 aluminum alloy material.(same to BMW's wheel hubs)
3. Random installation( vertical or horizontal)
4. Insulation class: F, Protection class: IP54
5. 100% oil free air delivery ( Impeller connected to the motor directly, without any oil lubricating) 
6. No routine maintenance (whithout wheel gear and belt,don't need to do maintenance towards those parts)
7. Quiet operation, low noise(adopt low noise motor, meanwhile inlay muffler is available if lower noise required)
8.Variable output control(pressure or vacuum)
9.Pulsation-free compression(use quakeproof footstand)
10.Long term durability(24H running)
11.Strictly tested before leaving the factory


Applications : 

1. Aquaculture (fish and prawn pond aeration)
2. Waste water treatment, sewage treatment system.
3. Pneumatic conveying systems.
4. Lifting and holding of parts by vacuum.
5. Packing machines.
6. Filling of bags/bottles/hoppers.
7. Soil remediation
8. Food processing.
9. Laser printers
10. Dental suction equipment.
11. Paper processing.
12. Gas analysis.



Our service:
 Marketing Service
100% tested CE certified blowers.Special customized blowers(ATEX blower,belt-driven blower) for special industry.Like gas transportation,Medical industry...Professional advice for model selection and further market development.
After-sale Service
Experienced suggestion for blower installation and use.12 months warranty.Long-term technical support.





FAQs:
Q: Can water be pumped through my blower?
A: No, clean dry air only
Q: My blower is leaking around the cover is this normal?
A: Normal goorui blowers are not  leak-free designed,but if you care a lot about the leaking,then you can contact us for a leak proof  one(special customized).
Q: What kind of oil do I need for my blower?
A: All our goorui blowers are oil-free and maintenance-free designed.
Q: Can I pump combustible gas through my blower?
A: Normally,if you'd like to use blower for combustible gas conveying,we suggest to choose our explosion proof ATEX blower(special customized) .
Q: Are the foam pieces inside my blower for filtration?
A: No, they are not for filtration. They are designed for sound reduction, an inlet filter should be sourced separately.
Q: What will be the consequences if I don't use a relief valve on my blower?
A: The blower may get overheat, and may cause thermal expansion of internal parts, which will do harm to the impeller and Bearing.

Lathe-mill Machining

CNC lathe milling compound as the name implies, that is, a CNC lathe and CNC Milling machine all features of a composite machine tool and its functions include turning milling compound, turning milling compound, milling compound, compound purpose is to make a machine tool with multiple functions, it can be a clamping to complete multiple tasks, Improve processing efficiency and processing accuracy, because it will be a numerical control lathe features combined with a machine will be above, greatly reduce the floor area, reduce the cost of capital such as rent. Although the numerical control milling composite unit price is higher, but because it can shorten the manufacturing process chain and the number of jigs and fixtures, workshop area and reduce equipment maintenance costs, considering it from the perspective of enterprise investment can also effectively reduce the overall fixed asset investment, greatly reduce the cost of production operations and personnel and equipment management.

It is widely used in the industry field, the process contained lath and milling, so it can seriously save time and operator. Save these means save money and also have the high quality tolerance.

We expect to be your best partner to meet your requirement, please send us your demand,we can give you the best suggestion.

Lathe-Mill Machining,Cnc Turning-Milling Machining,Cnc Machining Milling Turning,Milling Alloy Part

Suzhou FCE precision electronics Co., LTD , https://www.fcesz.com