2017 smart lighting will be connected to LED lighting

LED lighting has penetrated rapidly this year. After the popularity of LED lighting, smart lighting is expected to pick up in 2017. The industry expects that this wave of LED will be longer than in the past. LED Epistar faucet factory Jingyuan Optoelectronics, and package faucet Yiguang Optoelectronics is expected to benefit the most. This year, LED manufacturers increased their demand for lighting. In the first season of the first season, Jingdian set a record high in the single season, and revenue has rewritten a single monthly high for two consecutive months. Due to the full capacity of the second quarter, and the new products have been shipped, the company's product mix will be optimized, and the gross profit margin of the second quarter will increase significantly. The main reason for the rise in the gross profit margin of Jingdian is the high-voltage (HV) LED that is currently favored by international LED lighting manufacturers. Crystal Power is leading in this field and has received orders from major European manufacturers such as Philips. The monthly HV turnover is expected in this year. Multiply. In the first quarter of the year, Yiguang handed over a bright transcript. The single-quarter earnings per share (EPS) was 1 yuan (NTD, the same below), ranking first among LED listed companies, and the April revenue has led the rewrite list. With a record high in the month, the legal person estimates that the EPS of the second season of Yiguang is expected to reach 1.2 yuan, and there is an opportunity to challenge 5 yuan throughout the year. Yiguang is optimistic about the business opportunities brought by the LED lighting take-off. At present, it has actively built the channel. Following the purchase of German lighting channel manufacturers last year, this year plans to acquire European lighting distributors to show their enthusiasm for LED lighting. Li Bingjie, chairman of Jingdian, once said that the penetration rate of LEDs will increase rapidly this year. After crossing the S curve of permeability 10, it will show rapid growth. It is estimated that the US market will increase from 10 times to 20, and the penetration rate in the Japanese market. It will grow from 50 to 70, and the LED industry is expected to enter the gold for three years. Li Bingjie also stressed that after the rapid growth of LED lighting, it is estimated that there will be cross-era commodity pick-up after 2017, which is intelligent lighting. At present, Jingdian has started research and development. Yiguang Yefu also agrees with Li Bingjie's opinion. He emphasized that when LED lighting is popularized, intelligent lighting is a must to go, because LED lighting can save 85 power. If you apply intelligent lighting, you can save more than 90%. Achieved. Therefore, Everlight will not be absent in this field.

Excavator cylinder oil seals

â‘ Hardness:

Due to the scientific synthesis of high-molecular polyurethane elastomer materials using iron rubber, the higher the hardness, the higher the modulus, the smaller the elongation, and the better the wear resistance and heat resistance. Well, in the range of minus 35 degrees Celsius to 100 degrees Celsius, and at a pressure of 60 to 70 MPa, the maximum sealing performance can be guaranteed.

â‘¡Pressure resistance:

The use of viscoelastic seals made of nitrile rubber is the most complete protection against damage caused by back pressure. In the range of minus 55 degrees Celsius to 100 degrees Celsius, and under a pressure of 21MPa, due to the rubber The seal is often in a compressed state, so the compression performance of the rubber seal must be considered. It not only achieves enhanced anti-climbing performance and low friction resistance, but also has good performance in dealing with special low-temperature oil, and can also be used in combination with Anti-wear Ring double-purpose retaining ring BRL type.

â‘¢Prevention of oil leakage:

Sealing products made of polytetrafluoroethylene and nitrile rubber/PTFErubber; or seals made of nylon resin and nitrile rubber, which can be used in a wide range of applications with large pressure changes and fast sliding speeds According to the working condition, the input hydraulic pressure cutout is designed on the end face of the polytetrafluoroethylene ring to prevent penetration leakage. The maximum working temperature environment is minus 40 degrees Celsius to 160 degrees Celsius; the maximum working pressure is 50MPa.

SPGW piston seal

Material:PTFE+rubber elastomer+reinforced modified nylon
Temperature:Nitrile rubber -40~100℃
Speed:=1.0m/s
Pressure:≤50mpa

SPGO piston seal

Material:PTFE+rubber elastomer
Temperature:Nitrile rubber -40~110℃
Speed:=1.0m/s
Pressure:≤35mpa

SRUV piston rod seal

Material:NBR+thermoplastic polyurethane
Temperature: -35`90℃
Speed:=0.5m/s
Pressure:≤40mpa

SRS piston rod seal

Material:PTFE+NBR
Temperature:-40~110℃
Speed:=1.0m/s
Pressure:≤40mpa

SRCB piston rod buffer seal

Material:Polyurethane+modified polyoxymethylene
Temperature: -35~110℃
Speed:=1.0m/s
Pressure:≤50mpa

SRU piston rod seal

Material:Polyurethane
Temperature:-35~100℃
Speed:=1.0m/s
Pressure:≤40mpa

SRD iron case dust prevention

Material:Polyurethane+metal skeleton material
Temperature:-40~110℃
Speed:=1.0m/s

SRDI soft dustproof

Material:polyurethane
Temperature:-40~110℃
Speed:=1.0m/

SDS Dumbbell Seal

Material:polyurethane
Temperature: -35~110℃
Speed:=0.5m/s
Pressure:≤50mpa

SPG piston combination seal

Temperature:

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRNL piston rod seal

Material

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRDF Piston Rod Seal

Material

Polyester rubber

Temperature:-40`100℃

Speed:=1.0m/s

SDY Y-seal

Material:Polyurethane

Temperature:-35~110℃

Speed:=0.5m/s

Pressure:≤70mpa

KZT anti fouling ring

SDS Steffel

Piston main oil seal

oil seals,hydraulic oil seal,track link oil seal,TCV oil seal

Safe Seal Technology Co., Ltd. , https://www.jssafeseal.com